background image

 

 

 

Ver 1.2 6/15 

 

Precautions………………………………………………………………………………………….                                                                                      

 

Safety Tips…………………………………………………………………………………………….

                                                                                        

 

Please read this manual carefully before using the camera. 

 

Avoid damage from stress, violent vibration or liquid intrusion during 

transportation, storage or installation. 

 

Take care of the camera during installation to prevent damage to the camera 

case, ports, lens or PTZ mechanism. 

 

Do not apply excessive voltage. (Use only the specified voltage.) Otherwise, you 

may experience electrical shock. 

 

Keep the camera away from strong electromagnetic sources. 

 

Do not aim the camera at bright light sources (e.g. bright lights, the sun, etc.) for 

extended periods of time. 

 

Do not clean the camera with any active chemicals or corrosive detergents. 

 

Do not disassemble the camera or any of the camera's components.  If problems 

arise, please contact your authorized dealer. 

 

After long term operation, moving components can wear down.  Contact your 

authorized dealer for repair. 

 

Supplied Accessories…………………………………………………………………………….

                                                                       

 

 

HD Color Video Camera (1) 

 

12V/2.0A DC Power Adapter (1) 

 

Installation Bracket (1)  

 

Installation Screw (1) 

 

USB 3.0 Data Cable (3m), Serial Control Cable, RS-232C to RS-485 Adaptor 

 

IR Remote Controller (1) 

 

User Manual (1) 

 

 

Summary of Contents for 30X



















Reviews: