background image

MAINTENANCE 

SpikeShield

®

 Non-Modular Surge Protective Device (SPD)

19

 

Hubbell Wiring Devices

 1-800-729-3406 | www.Hubbell-Wiring.com

06/2010 

8222-0507A

Maintenance and 
Troubleshooting

Preventive Maintenance

Inspect the SPD periodically to maintain reliable system performance and 
continued transient voltage surge suppression. Periodically check the state 
of the diagnostic display panel LED status indicators. Routinely use the 
built-in diagnostics to inspect for inoperative modules

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe 

electrical work practices. See NFPA 70E.

• This equipment must only be installed and serviced by qualified 

electrical personnel.

• Turn off

 

all power supplying this equipment before working on or inside 

equipment.

• Always use a properly rated voltage sensing device to confirm power is off.

• Replace all devices, doors and covers before turning on power to this 

equipment.

• This equipment must be effectively grounded per all applicable codes. 

Use an equipment-grounding conductor to connect this equipment to 
the power system ground.

Failure to follow these instructions will result in death or serious injury.

Summary of Contents for SPIKESHIELD HBL10P120B





















Reviews: