Huawei U8815 Maintenance Manual Download Page 74

Page: 74 / 80

U8815
Maintenance Manual

9 Principles and Failure Analysis

Issue 1.0 (2012-02-13)

Huawei Proprietary and Confidential

Figure 9-54

Troubleshooting process for FM radio failure

Is the FM

channel search effect

good after the headset is

replaced?

Is the FM

channel search effect

good after the headset holder is

checked and

re-soldered?

Is the FM

channel search effect

good after the software is

updated?

End

The FM channel search

effect is not good.

Return the headset to the

factory for repair.

Table 9-15 describes the signals in the circuit diagram in this section.

Table 9-15

Description of the signals in the circuit diagram in this section

Signal

Description

Reference Measurement
or Wave Form

FM_ANT

FM antenna

None

SR_AVDD2P5 Supplies power to the BCM4330 chip

2.5 V

VDD_LN_1P2 Supplies power to the BCM4330 chip

1.2 V

FM_OUT_L

The signal is output from the FM.

None

FM_OUT_R

The signal is output from the FM.

None

Summary of Contents for U8815

















































































Search results

Summary of Contents for U8815

Reviews:

Related manuals for U8815

Brands by name

Popular brands

Huawei U8815, Maintenance Manual

Search results

Summary of Contents for U8815

Reviews:

Related manuals for U8815

Brands by name

Popular brands