Huawei U8815 Maintenance Manual Download Page 38

Page: 38 / 80

U8815
Maintenance Manual

9 Principles and Failure Analysis

Issue 1.0 (2012-02-13)

Huawei Proprietary and Confidential

Figure 9-10

Troubleshooting process for charging failures

Is voltage available on C1014?

Check the fuse F101 and

the electromagnetic

interface bead LB301.

After being connected to

a charger, the handset

cannot be charged.

End

Solder J103.

Replace U1001.

Replace the charger.

Does pin 3 of

Q201 provide output?

Replace Q201.

Is the J1501 battery

connector damaged?

Replace the J1501

battery connector.

Is the battery damaged?

Replace the battery.

Is the

output voltage VPH_PWR

available on the U1001

charging chip?

Does the J103 USB

connector need to

be soldered?

Does the charger

work properly?

Table 9-2 describes the signals in the circuit diagram in this section.

Summary of Contents for U8815

















































































Search results

Summary of Contents for U8815

Reviews:

Related manuals for U8815

Brands by name

Popular brands

Huawei U8815, Maintenance Manual

Search results

Summary of Contents for U8815

Reviews:

Related manuals for U8815

Brands by name

Popular brands