manualshive.com logo in svg

Huawei U8815, Maintenance Manual

Share
Download
Huawei U8815 Maintenance Manual Download Page 67

U8815 
Maintenance Manual 

9 Principles and Failure Analysis 

 

Issue 1.0 (2012-02-13) 

Huawei Proprietary and Confidential           

Copyright © Huawei Technologies Co., Ltd. 

58 

 

Figure 9-45

 

Troubleshooting process for no sound from the headset failure 

Is the receiver 

volume setting normal?

Is the call normal after the 

headset is replaced?

Does the 

voltage change after the 

headset HS_DETECT is 

inserted?

Replace the 

headset holder.

Y

N

Y

N

Y

N

Reset the 

receiver volume.

End

After a call is 

established, on sound is 

heard over the headset.

Return the headset to 

the factory for repair.

 

 

Table 9-12 describes the signals in the circuit diagram in this section. 

Table 9-12

 

Description of the signals in the circuit diagram in this section 

Signal 

Description   

Reference Measurement or 
Wave Form 

FM_ANT 

FM antenna   

None 

HPH_OUT_L 

Stereo headset output 

None 

HPH_OUT_R 

Stereo headset output 

None 

HSED_MICBIAS 

Headset microphone bias voltage   

Voltage signal 

MIC2_P 

Input from the headset microphone 

None 

MIC2_N 

Input from the headset microphone 

None 

HSED_ADC_DET  Headset microphone test 

Voltage change 

HS_DETECT 

Headphone connect test 

Voltage change 

GND_MIC3 

Headset MIC grounding signal 

None 

 

Summary of Contents for U8815

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands