Huawei U8650 Maintenance Manual Download Page 85

Page: 85 / 101

U8950 Maintenance Guide V1.0

10 Principles and Failure Analysis

2012-10-22

Huawei Proprietary and Confidential

MIC1_N

Primary microphone input

None

AUXI_P

Secondary microphone
input

None

AUXI_N

Secondary microphone
input

None

MSM_MICBI
AS

Bias voltage of the primary
microphone

None

MICBIAS_SI

Bias voltage of the
secondary microphone

None

10.3.5 Headset

Circuit Block Diagram

Working Principle

The earphone connect status is identified according to the HS_DETECT_N (GPIO_026).

Before connecting the headphone, HS_DETECT_N is pulled up to high level by VREG_S3.

After connecting the headphone, HS_DETECT_N is dropped down to low level.

The headphone MIC is supplied with power by MIC_BIAS1 (PM8029/HSED_BIAS1), and it
is used for headphone answer detection.

U8950’s headphone is compatible with two line sequences. The iphone's headphone line
sequence is compatible by default. The pull-up voltage is L10 3V.

Summary of Contents for U8650






































































































Search results

Summary of Contents for U8650

Reviews:

Related manuals for U8650

Brands by name

Popular brands

Huawei U8650, Maintenance Manual

Search results

Summary of Contents for U8650

Reviews:

Related manuals for U8650

Brands by name

Popular brands