Huawei U8650 Maintenance Manual Download Page 38

Page: 38 / 101

U8950 Maintenance Guide V1.0

9 Maintenance Records During Verification

2012-10-22

Huawei Proprietary and Confidential

Stage

Station of Fault

Faulty Item

Symptom

Solution

MMI

MMI01F
abnormal
display

The software was
poorly loaded.

The test was performed again after
the software was eliminated.

MMI

MMI01E
display
malfunction

The LCD BTB
connector on the
main PCBA was
poorly soldered.

The BTB connector was re-soldered.

MMI

MMI01D
automatic
restart or
power-off

The side key FPC
was short-circuited,
resulting in
automatic startup (or
turn-off).

The side key FPC was to be
replaced.

MMI

MMI01B
startup failure

The side key FPC
was broken,
resulting in startup
failure after the
power key was
pressed.

The side key FPC was to be
replaced.

MMI

MMI01B
startup failure

The board clip on
the front cover was
broken, resulting in
poor contact
between the board
and startup shrapnel
on the front cover.

The front cover was to be replaced.

MMI

MMI01B
startup failure

The startup shrapnel
on the main PBCA
failed to contact the
FPC.

The startup shrapnel and FPC were
re-assembled.

CT20001Y

The test equipment
was unstable.

No current leakage was detected
when tested using a multimeter. The
test equipment was replaced and the
test then passed.

CT200011

The flash chip was
open soldered.

The test was performed again and no
interface was detected yet. However,
it passed after the flash chip was
re-soldered.

CT 200011

The resistor R3802
had a side effect.
The software was
not programmed
properly.

The test failed after the resistor was
re-soldered and passed after the
software was re-programmed.

BT367329
BER

A mis-test occurred.

The test was performed again.

Summary of Contents for U8650






































































































Search results

Summary of Contents for U8650

Reviews:

Related manuals for U8650

Brands by name

Popular brands

Huawei U8650, Maintenance Manual

Search results

Summary of Contents for U8650

Reviews:

Related manuals for U8650

Brands by name

Popular brands