Huawei U8650 Maintenance Manual Download Page 50

Page: 50 / 101

U8950 Maintenance Guide V1.0

9 Maintenance Records During Verification

2012-10-22

Huawei Proprietary and Confidential

Stage

Station of Fault

Faulty Item

Symptom

Solution

VN1

Upload

B03A

REG_S4 output
nothing, all voltages
were not stable,
and U1002
and U1402 were
short-circuited

U1002 and U1402 were found
connected. Report this problem to
R&D for further analysis.

VN1

Upload

Upload fails

U3801 was
short-circuited, and
VREG_S4 output
nothing.

U3801 was found defective, which is
reported to R&D for further analysis.

VN1

Upload

Upload fails

No port was found.

The VREG_S3 voltage was 3.6 V,
and VREG_S4 output nothing. It is
determined that U201 is faulty. Keep
the sample for further analysis.

VN1

568214

The coaxial cable
was poorly
connected to the
sub-board.

Check with the production line and
R&D first, re-connect the cable to
the sub-board, and test again.

VN1

300031

C3502 has a current
leakage of 1.5 mA.

Remove C3502 and test again.

Summary of Contents for U8650






































































































Search results

Summary of Contents for U8650

Reviews:

Related manuals for U8650

Brands by name

Popular brands

Huawei U8650, Maintenance Manual

Search results

Summary of Contents for U8650

Reviews:

Related manuals for U8650

Brands by name

Popular brands