background image

Installing the Device into a Cabinet 

Install the Device into the Cabinet Through L Guid

1

1

3

1

Fix the mounting ears to the chassis using M4 screws.

3

Place the device on the guide rails and push it into the cab
mounting bar of the cabinet. Fix the device to the cabinet u

Install the Device into the Cabinet Through Rear M

z

This method is applicable to any 19-inch standard cabinet.

z

If interface cards are to be installed in the front of the cabinet, 

side, and screws for rear mounting ears at the power supply side;
front mounting ears should be installed at the power supply side,

1

1

3

2

1

At both sides of the rear of the cabinet, install 
captive nuts in holes 1 and 3 for a 1U height. Fix 
rear mounting ears to the cabinet using M6 screws.

3

5

de Rails

2

2

1

2

Bottom of the 

2

Install L guide rails and captive nuts. Align the lower 
edges of the guide rails with the narrow edge of the 
mounting bar of the cabinet. Install captive nuts into 
holes 1 and 2 in the figure. The installation of the 
guide rail on the left is identical with that on the right.

guide rail

binet until the mounting ears touch the 

using M6 screws.

This method is applicable only to Huawei 19-inch standard
cabinet.

Mounting Ears

front mounting ears should be installed at the interface card 

; if the power supply is to be installed in the front of the cabinet, 

 and screws for rear mounting ears at the interface card side.

2

Install the screws for front and rear mounting ears 
at both sides of the chassis.

2

Pl

th d

i

i t th

bi

t

ith th

t

3

5

Place the device into the cabinet with the screws at rear 
of the device touching the rear mounting ears. Push the 
device until the front mounting ears touch the mounting 
bar of the cabinet. Fix the front mounting ears of the 
device to the cabinet using M6 screws.

3

Summary of Contents for SVN2000 Series











Reviews: