manualshive.com logo in svg

Huawei SUN2000-50KTL-JPM0, User Manual, Page: 81 / 113

Share
Download
Huawei SUN2000-50KTL-JPM0 User Manual Download Page 81

SUN2000-(50KTL-JPM0, 50KTL-JPM1, 63KTL-JPM0) 
User Manual 

7 Man-Machine Interactions 

 

Issue 01 (2018-09-30) 

Copyright © Huawei Technologies Co., Ltd. 

75 

 

No. 

Parameter  Description 

Unit  Default 

Value 

Value Range 

Remarks 

12 

String 
connection 
mode 

Specifies the 
connection mode of 
PV strings. 

 

When the PV 
strings connect to 
the inverter 
separately (fully 
separate 
connection), there 
is no need to set 
this parameter. 
The inverter can 
automatically 
detect the 
connection mode 
of the PV strings. 

 

When the PV 
strings connect to 
one another in 
parallel outside the 
inverter and then 
connect to the 
inverter 
independently 
(fully parallel 
connection), set 
this parameter to 

All PV strings 
connected

. 

N/A 

Automatic 
detection 

 

Automatic 
detection 

 

All PV 
strings 
separated 

 

All PV 
strings 
connected 

N/A 

13 

Communic
ation 
interrupt 
shutdown 

The standards of 
certain countries and 
regions require that 
the SUN2000 must 
shut down after the 
communication is 
interrupted for a 
certain time. 

N/A 

Disable 

 

Disable 

 

Enable 

If 

Communication 

interrupt shutdown

 

is set to 

Enable

 and 

the SUN2000 
communication has 
been interrupted for 
a specified time (set 
by 

Communication 

interruption 
duration

), the 

SUN2000 will 
automatically shut 
down. 

Summary of Contents for SUN2000-50KTL-JPM0


















































































































Reviews:

No comments