manualshive.com logo in svg

Huawei SUN2000-50KTL-JPM0, User Manual, Page: 13 / 113

Share
Download
Huawei SUN2000-50KTL-JPM0 User Manual Download Page 13

SUN2000-(50KTL-JPM0, 50KTL-JPM1, 63KTL-JPM0) 
User Manual 

2 Overview 

 

Issue 01 (2018-09-30) 

Copyright © Huawei Technologies Co., Ltd. 

7 

 

LED 

Status 

Meaning 

Communication LED 

 

Blinking green (on for 0.2s and then off 
for 0.2s) 

The SUN2000 receives data over 
RS485 communication. 

Off 

The SUN2000 has not received data 
over RS485 communication for 10 
seconds. 

Alarm/Maintenance LED 

 

Alarm status 

Blinking red at long 
intervals (on for 1s and 
then off for 4s) 

The SUN2000 is generating a warning 
alarm. 

Blinking red at short 
intervals (on for 0.5s 
and then off for 0.5s) 

The SUN2000 is generating a minor 
alarm. 

Steady red 

The SUN2000 is generating a major 
alarm. 

Local 
maintenance 
status 

Blinking green at long 
intervals (on for 1s and 
then off for 1s) 

Local maintenance is in progress. 

Blinking green at short 
intervals (on for 0.125s 
and then off for 0.125s) 

Local maintenance fails. 

Steady green 

Local maintenance is successful. 

 

 

 

Local maintenance refers to operations performed after a USB flash drive, Bluetooth module, or 
USB data cable is inserted into the USB port of the SUN2000. For example, local maintenance 
includes configuration import and export using a USB flash drive, and maintenance operations on 
the SUN2000 app installed on a device connected to the SUN2000 by a Bluetooth module or USB 
data cable. 

 

If an alarm occurs during local maintenance, the Alarm/Maintenance LED shows the local 
maintenance status first. After the USB flash drive, Bluetooth module, or USB data cable is removed, 
the LED shows the alarm status. 

Bottom View 

 

Summary of Contents for SUN2000-50KTL-JPM0


















































































































Reviews:

No comments