Huawei SUN2000-50KTL-JPM0 User Manual Download Page 105

Page: 105 / 113

SUN2000-(50KTL-JPM0, 50KTL-JPM1, 63KTL-JPM0)
User Manual

9 Handling the Inverter

Issue 01 (2018-09-30)

Handling the Inverter

9.1 Removing the SUN2000

Before removing the SUN2000, disconnect both the AC and DC power supplies. For details
about the power-off process, see

6.3 Powering Off the System

. After powering off the

SUN2000, wait at least 15 minutes before performing operations on it.

To remove the SUN2000, perform the following steps:

Disconnect all cables from the SUN2000, including RS485 communications cables, DC
input power cables, AC output power cables, and PE cables.

Remove the SUN2000 from the mounting bracket.

Remove the mounting bracket.

9.2 Packing the SUN2000



If the original packing materials are available, put the SUN2000 inside them and then
seal them by using adhesive tape.



If the original packing materials are not available, put the SUN2000 inside a suitable
cardboard box and seal it properly.

9.3 Disposing of the SUN2000

If the SUN2000 service life expires, dispose of it according to the local disposal rules for
electrical equipment waste.

Summary of Contents for SUN2000-50KTL-JPM0


















































































































Search results

Summary of Contents for SUN2000-50KTL-JPM0

Reviews:

Related manuals for SUN2000-50KTL-JPM0

Brands by name

Popular brands

Huawei SUN2000-50KTL-JPM0, User Manual

Search results

Summary of Contents for SUN2000-50KTL-JPM0

Reviews:

Related manuals for SUN2000-50KTL-JPM0

Brands by name

Popular brands