Huawei SUN2000-50KTL-JPM0 User Manual Download Page 51

Page: 51 / 113

SUN2000-(50KTL-JPM0, 50KTL-JPM1, 63KTL-JPM0)
User Manual

5 Electrical Connections

Issue 01 (2018-09-30)

Figure 5-16

Measuring voltage



If the voltage is a negative value, the PV string is of reversed polarity. Correct before
connecting this string to the SUN2000.



If the voltage is greater than 1100 V, too many PV modules are configured to the same
string. Remove some PV modules.

Step 3

Pull out the blue dustproof plugs from the ends of the DC input connectors.

Before performing

Step 4

, ensure that the two DC switches are OFF.

Step 4

Insert the positive and negative connectors into the corresponding positive and negative DC
input terminals of the SUN2000 until they snap into place.

After the positive and negative connectors snap into place, pull test to the DC input power
cable is recommended.

Summary of Contents for SUN2000-50KTL-JPM0


















































































































Search results

Summary of Contents for SUN2000-50KTL-JPM0

Reviews:

Related manuals for SUN2000-50KTL-JPM0

Brands by name

Popular brands

Huawei SUN2000-50KTL-JPM0, User Manual

Search results

Summary of Contents for SUN2000-50KTL-JPM0

Reviews:

Related manuals for SUN2000-50KTL-JPM0

Brands by name

Popular brands