Huawei SUN2000-33KTL User Manual Download Page 88

Page: 88 / 98

SUN2000-(33KTL, 40KTL)
User Manual

9 SUN2000 Handling

Issue 03 (2015-12-01)

Huawei Proprietary and Confidential

SUN2000 Handling

9.1 Removing the SUN2000

This section describes how to remove the SUN2000.

Perform the following operations to remove the SUN2000:

Disconnect all cables from the SUN2000, including RS485 communications cables, DC
input power cables, AC output power cables, and PGND cables.

(Optional) Open the anti-theft lock at the bottom of the SUN2000.

Remove the SUN2000 from the rear panel.

Remove the rear panel.

9.2 SUN2000 Packing

This section describes how to pack the SUN2000.



If the original packing case is available, place the SUN2000 inside the packing case and
seal it with adhesive tape.



If the original packing case is unavailable, place the SUN2000 inside a suitable hard
carton and seal it properly.

9.3 SUN2000 Disposal

This section describes how to dispose of the SUN2000.

If the SUN2000 service life has expired, dispose of the SUN2000 in accordance with local
rules for disposal of electrical equipment waste, or return the SUN2000 to Huawei.

Summary of Contents for SUN2000-33KTL



































































































Search results

Summary of Contents for SUN2000-33KTL

Reviews:

Brands by name

Popular brands

Huawei SUN2000-33KTL, User Manual

Search results

Summary of Contents for SUN2000-33KTL

Reviews:

Brands by name

Popular brands