Huawei SUN2000-33KTL User Manual Download

Page: 35 / 98

SUN2000-(33KTL, 40KTL)
User Manual

4 Installation

Issue 03 (2015-12-01)

Huawei Proprietary and Confidential

Figure 4-8

Moving the SUN2000

Step 2

Carry the SUN2000 out of the packing case and move it to the installation position.



To prevent device damage and personal injury, keep balance when moving the SUN2000
which is heavy.



Do not place the SUN2000 with its wiring terminals contacting the floor because the
power ports and signal ports at the bottom of the device are not designed to support the
weight of the SUN2000. Place the SUN2000 horizontally.



When placing the SUN2000 on the floor, put foam or paper under the SUN2000 to protect
its enclosure.

----End

4.3.3 Installing a Rear Panel

Before installing the SUN2000, secure the shipped rear panel to a wall.

Prerequisites

Figure 4-9

shows the dimensions of the rear panel.

Summary of Contents for SUN2000-33KTL



































































































Search results

Summary of Contents for SUN2000-33KTL

Reviews:

Related manuals for SUN2000-33KTL

Brands by name

Popular brands

Huawei SUN2000-33KTL, User Manual

Search results

Summary of Contents for SUN2000-33KTL

Reviews:

Related manuals for SUN2000-33KTL

Brands by name

Popular brands