Huawei SUN2000-33KTL User Manual Download Page 16

Page: 16 / 98

SUN2000-(33KTL, 40KTL)
User Manual

2 Overview

Issue 03 (2015-12-01)

Huawei Proprietary and Confidential

No.

Component Name (Silk Screen) Description

DC switch (DC SWITCH)

N/A

Positive DC input terminal (+)

Six routes

USB port (USB)

N/A

RS485 port (COM1)

N/A

Protective earthing (PE) bolt

N/A

AC output port (AC OUTPUT)

N/A

Vent valve

2 PCS

Negative DC input terminal (-)

Six routes

Antenna (ANT)

Reserved WiFi port

RS485 port (COM2)

N/A

2.3 Label Conventions

This section describes the symbols and nameplate on the SUN2000-33KTL/40KTL.

Symbols

Table 2-3

describes all symbols on the SUN2000-33KTL/40KTL.

Table 2-3

Symbols

Symbol

Label

Meaning

Delay discharge



There are high voltages
when this SUN2000 is
running. Only qualified
and trained electrical
technicians are allowed
to perform operations
on the SUN2000.



There are residual
voltages in the
SUN2000. It needs 5
minutes to finish
discharge.

Burn warning

The SUN2000 must not be
touched when in operation
because its enclosure and
heat sinks are extremely
hot.

Summary of Contents for SUN2000-33KTL



































































































Search results

Summary of Contents for SUN2000-33KTL

Reviews:

Brands by name

Popular brands

Huawei SUN2000-33KTL, User Manual

Search results

Summary of Contents for SUN2000-33KTL

Reviews:

Brands by name

Popular brands