Huawei SUN2000-33KTL User Manual Download

Page: 83 / 98

SUN2000-(33KTL, 40KTL)
User Manual

8 Maintenance

Issue 03 (2015-12-01)

Huawei Proprietary and Confidential

Alarm ID Alarm

Name

Alarm
Severity

Causes

Measures

200

DC Bus
Voltage
Fault

Major

Abnormal external conditions
have triggered the protection
for the DC circuits inside the
SUN2000. The possible causes
are as follows:



Reason ID = 3

The SUN2000 input is
suddenly disconnected, or
the PV strings shielded
result in a sharp change in
output power.



Reason ID = 9 or 11

The input energy of the
SUN2000 cannot be vented
quickly due to the sharp
change of grid voltage. As
a result, the internal
voltage increases.



Reason ID = 10

The internal control circuit
of the SUN2000 has failed
to keep pace with changes
due to grid phase
imbalance.

The SUN2000 monitors its
external working conditions in
real time and automatically
recovers to the normal operating
status after the fault is rectified.

If the alarm occurs repeatedly,
contact Huawei technical
support.

Summary of Contents for SUN2000-33KTL



































































































Search results

Summary of Contents for SUN2000-33KTL

Reviews:

Related manuals for SUN2000-33KTL

Brands by name

Popular brands

Huawei SUN2000-33KTL, User Manual

Search results

Summary of Contents for SUN2000-33KTL

Reviews:

Related manuals for SUN2000-33KTL

Brands by name

Popular brands