Huawei SUN2000-20KTL-M3 User Manual Download Page 54

Page: 54 / 95

6.2 System Power-On

Prerequisites

NO TICE

● Before turning on the AC switch between the SUN2000 and the power grid,

check that the AC voltage is within the specified range using a multimeter.

● If the DC power supply is connected but the AC power supply is disconnected,

the SUN2000 will report a Grid Loss alarm. The SUN2000 can start properly

only after the power grid recovers.

Procedure

Step 1 Turn on the AC switch between the SUN2000 and the power grid.
Step 2 (Optional) Remove the locking screw beside the DC switch.

Figure 6-1 Removing the locking screw beside the DC switch

Step 3 Turn on the DC switch at the bottom of the SUN2000.
Step 4 Observe the LED indicators to check the operating status of the SUN2000.

Table 6-2 Indicator description

Category

Status

Description

Running

indicator

LED1

LED2

–

Steady green

The SUN2000 is

operating in grid-

tied mode.

Blinking green

slowly (on for 1s

and off for 1s)

Off

The DC is on and

the AC is off.

SUN2000-(20KTL, 29.9KTL, 30KTL, 36KTL, 40KTL)-

User Manual

6 Commissioning

Issue 01 (2020-10-15)

Summary of Contents for SUN2000-20KTL-M3
































































































Search results

Summary of Contents for SUN2000-20KTL-M3

Reviews:

Brands by name

Popular brands

Huawei SUN2000-20KTL-M3, User Manual

Search results

Summary of Contents for SUN2000-20KTL-M3

Reviews:

Brands by name

Popular brands