Huawei SUN2000-100KTL User Manual Download Page 129

Page: 129 / 156

Alarm

Name

Alarm

Severit

Possible Causes

Suggestions

2067

Faulty

Power

Collector

Major

Cause ID = 1
The power meter is disconnected.

1. Check whether the

configured power meter

model is the same as the

actual model.

2. Check whether the

communications

parameters of the power

meter are the same as the

RS485 configurations of

the solar inverter.

3. Check whether the power

meter is powered on and

whether the RS485

communications cable is

connected.

2085

Built-in

PID

operatio

abnorm

Minor

Cause ID = 1, 2
● The output resistance of PV

arrays to ground is low.

● The system insulation

resistance is low.

● Cause ID = 1

1. Turn off the AC output

switch and DC input

switch, wait for a period

of time (for details

about the wait time, see

the description on the

device safety warning

label), and then turn on

the DC input switch and

AC output switch.

2. If the alarm persists,

contact your dealer or

Huawei technical

support.

● Cause ID = 2

1. Check the impedance

between the PV array

output and the ground.

If a short circuit occurs

or the insulation is

insufficient, rectify the

fault.

2. If the alarm persists,

contact your dealer or

Huawei technical

support.

SUN2000-(75KTL, 100KTL, 110KTL, 125KTL) Series

User Manual

8 Maintenance

Issue 11 (2021-11-10)

120

Summary of Contents for SUN2000-100KTL





























































































































































Search results

Summary of Contents for SUN2000-100KTL

Reviews:

Related manuals for SUN2000-100KTL

Brands by name

Popular brands

Huawei SUN2000-100KTL, User Manual

Search results

Summary of Contents for SUN2000-100KTL

Reviews:

Related manuals for SUN2000-100KTL

Brands by name

Popular brands