Huawei SUN2000-100KTL User Manual Download Page 136

Page: 136 / 156

8.6 Loading the DC Switch

NO TE

The DC switches can turn off automatically in the case of internal failures of inverters.

Prerequisites

If internal inverter fault is displayed on the mobile app or remote monitoring

system and the DC switch is OFF, the DC switch of the inverter has been

automatically turned off. In this case, rectify the fault based on the alarm

handling suggestions before turning on the DC switch.

Procedure

Step 1 Loosen the nuts on the RESET buttons under the three DC switches.
Step 2 Press the RESET buttons until it cannot go further, and then tighten the nuts of

the RESET buttons.

Figure 8-18 Loading the DC switch (DC SWITCH 1 is used as an example)

----End

SUN2000-(75KTL, 100KTL, 110KTL, 125KTL) Series

User Manual

8 Maintenance

Issue 11 (2021-11-10)

127

Summary of Contents for SUN2000-100KTL





























































































































































Search results

Summary of Contents for SUN2000-100KTL

Reviews:

Brands by name

Popular brands

Huawei SUN2000-100KTL, User Manual

Search results

Summary of Contents for SUN2000-100KTL

Reviews:

Brands by name

Popular brands