Huawei SMU01C User Manual Download Page 44

Page: 44 / 54

SMU01C
User Manual

9 Alarm Management

Issue 03 (2015-01-05)

Huawei Proprietary and Confidential

Measures

Adjust the ambient temperature alarm threshold to a proper range.

Replace the faulty temperature sensor.

9.5.10 Batt Operation

Possible Causes



An AC outage occurs.



A rectifier is faulty.

Measures

Check whether an alarm is generated for an AC outage or a faulty rectifier. Rectifier the fault
by referring to related troubleshooting measures.

9.5.11 Batt Over Curr

Possible Causes



The rectifier fails to communicate with the monitoring unit.



Storage batteries are faulty.

Measures

If a rectifier is not connected properly, reset and secure it.

Check the storage batteries, and replace faulty ones.

9.5.12 Load Fuse Trip

Possible Causes



The load circuit breaker is OFF.



The circuit breaker detection wire is loose.

Measures

Check the load circuit breaker. If the load circuit breaker is off but not because of short
circuit, switch on the load circuit breaker.

If the circuit breaker detection wire is loose, secure it.

Check whether the voltage at both ends of the circuit breaker is near 0 V using a
multimeter. If yes, the circuit breaker is functional. If no, replace the circuit breaker
because it is faulty.

If the alarm persists after the load circuit breaker is replaced, replace the monitoring unit
because the alarm loop is faulty.

9.5.13 Batt. loop Trip

Possible Causes



The battery circuit breaker is OFF

Summary of Contents for SMU01C























































Search results

Summary of Contents for SMU01C

Reviews:

Related manuals for SMU01C

Brands by name

Popular brands

Huawei SMU01C, User Manual

Search results

Summary of Contents for SMU01C

Reviews:

Related manuals for SMU01C

Brands by name

Popular brands