manualshive.com logo in svg

Huawei SmartAX MT800, User Manual

Share
Download
Huawei SmartAX MT800 User Manual Download Page 94

 

84 

Configurations on MT800 

Location 

Parameters 

Comments  

Encapsulation 

The value shall be provided by your ISP. 
Usually you can keep the default value: 
LLC. 

Connection Type  Select “RFC2684 Bridged”. 

Address Type 

Select “Static IP”. 

 

IP Address and 
Subnet Mast 

The values shall be provided by your ISP. 

Default Route 

Select “Enable”. 

ATM Setting 

Gateway IP 
Address 

The value shall be provided by your ISP. 

NAT 

It is recommended to enable the function of NAT. 

DNS 

It is recommended to have DNS Relay function enabled. 

And set DNS IP address provided by your ISP. 

DHCP Mode 

It is recommended to have DHCP Server function enabled. 

Traffic Index 

It is recommended to set 0. 

Configurations on the user’s PC 

IP Address and 

Network Mask 

It is recommended to set the mode as obtaining an IP address 

automatically. 

DNS 

It is recommended to set the mode as obtaining a DNS server’s 

IP address automatically.  

 

Summary of Contents for SmartAX MT800














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands