manualshive.com logo in svg

Huawei SmartAX MT800, User Manual

Share
Download
Huawei SmartAX MT800 User Manual Download Page 87

 

77 

  Caution: 

Do not reboot the device using the Reset button on the back panel of the MT800 to 
activate new changes. This button resets the device settings to the manufacturer’s 
default values. Any custom settings will be lost. 

 

4.20  

Firmware Upgrade 

Click the hyperlink 

Firmware Upgrade

 in the Wizard column to 

open the 

Firmware Upgrade

 page and update the system software.  

 

Figure 4-43

 

Firmware upgrade 

Upgrade File:

 Type in the full path and file name of the firmware 

file to be uploaded. Alternatively you may click the Browse button to 
search for the file on your system. 

When the file names have been entered, click the 

Upload

 

button to start loading the firmware file. If the upload is successful, a 
message informs you that it was successfully loaded. If the firmware 
does not load, an error message informs you to try the upload again. 
Check the file names and attempt to upload again. If the file still is not 
loaded, reboot the device and try again. 

Summary of Contents for SmartAX MT800














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands