Huawei RRU3642 Installation Manual Download Page 11

Page: 11 / 130

05 (2013-06-26)

This is the fifth official release.

Compared with issue 04 (2013-04-28), this issue includes the following change:

Topic

Change Description

8.10 Installing an RRU Power Cable

Added the power device DCDU-12B for the
RRU.

Compared with issue 04 (2013-04-28), this issue does not include any new information and no
information is deleted from this issue.

04 (2013-04-28)

This is the fourth official release.

Compared with issue 03 (2013-01-14), this issue includes the following new information:

7.6 Installing an RRU on an IFS06

Compared with issue 03 (2013-01-14), this issue includes the following change:

Topic

Change Description

The whole document

Modified the figures showing the mounting kits for
an RRU, which have been modified.

About This Document

Changed the document name from

RRU3942

Installation Guide

RRU3942&RRU3642

Installation Guide

2.2 Tools and Instruments

Modified the specifications of the hammer drill and
wrench.

3.4 Installation Scenarios

Modified the installation scenarios of the RRU.

4 Unpacking the Equipment

Added requirements for checking the insulation layer
of RRU cables.

7 Installing the RRU

Changed the procedures for installing the RRU in
different scenarios because RRU mounting kits and
attachment plates are redesigned.

8.1 Cabling Requirements

Added requirements for routes of RRU cables.

Compared with issue 03 (2013-01-14), no information is deleted from this issue.

03 (2013-01-14)

This is the third official release.

RRU3942&RRU3642
Installation Guide

1 Changes in the RRU3942&RRU3642 Installation Guide

Issue 07 (2013-12-30)

Huawei Proprietary and Confidential

Summary of Contents for RRU3642



































































































































Search results

Summary of Contents for RRU3642

Reviews:

Related manuals for RRU3642

Brands by name

Popular brands

Huawei RRU3642, Installation Manual

Search results

Summary of Contents for RRU3642

Reviews:

Related manuals for RRU3642

Brands by name

Popular brands