Huawei RRU3642 Installation Manual Download Page 21

Page: 21 / 130

Item

Silkscreen

Description

RX_IN/OUT

Interconnection port

RET

Communication port for the RET antenna,
supporting RET signal transmission

(2) Ports in the cabling
cavity

RTN(+)

Power supply socket

NEG(-)

CPRI0

Optical/electrical port 0

CPRI1

Optical/electrical port 1

EXT_ALM

Alarm monitoring port used for monitoring
one RS485 signal and two dry contact signals

(3) Indicators

RUN

See

3.3 RRU Indicators

ALM

ACT

VSWR

CPRI0/IR0

CPRI1/IR1

NOTE

The port for transmitting RET signals is determined by the software.

For the RRU3942, both CPRI0 and CPRI1 can be conected to the BBU. Use the CPRI0 by default in
the single-mode scenario.

For the RRU3642, CPRI0 is connected to the BBU and the CPRI1 is reserved. The RX_IN/OUT is not
used.

Table 3-2

describes how to use RF ports for RRU3942.

RRU3942&RRU3642
Installation Guide

3 Information About the Installation

Issue 07 (2013-12-30)

Huawei Proprietary and Confidential

Summary of Contents for RRU3642



































































































































Search results

Summary of Contents for RRU3642

Reviews:

Related manuals for RRU3642

Brands by name

Popular brands

Huawei RRU3642, Installation Manual

Search results

Summary of Contents for RRU3642

Reviews:

Related manuals for RRU3642

Brands by name

Popular brands