Huawei RRU3201 Installation Manual Download Page 62

Page: 62 / 96

Figure 7-29

Distance between the main mounting bracket and the ground

NOTE

It is recommended that the main mounting bracket be 1,200 mm (47.24 in.) to 1,600 mm (62.99 in.)
above the ground.

Step 2

Fit one end of the auxiliary mounting bracket to one dual-nut bolt assembly of the main mounting
bracket.

Step 3

Install the bracket assembly on angle steel, and then fit the other end of the auxiliary mounting
bracket to the other dual-nut bolt assembly, as shown in

Figure 7-30

Installing the bracket assembly

NOTE

Verify that the arrow on the main mounting bracket is pointing up.

Step 4

Using a torque wrench, tighten the nuts to 40 N·m (354.03 lbf·in.) to secure both the bracket
assembly onto the angle steel, as shown in

Figure 7-31

RRU3201
Installation Guide

7 Installing the RRU

Issue 06 (2012-04-16)

Huawei Proprietary and Confidential

Summary of Contents for RRU3201

































































































Search results

Summary of Contents for RRU3201

Reviews:

Related manuals for RRU3201

Brands by name

Popular brands

Huawei RRU3201, Installation Manual

Search results

Summary of Contents for RRU3201

Reviews:

Related manuals for RRU3201

Brands by name

Popular brands