Huawei RRU3201 Installation Manual Download Page 84

Page: 84 / 96

Connect the other end of the AISG extension cable to the standard AISG male
connector on the RCU, as shown in

Figure 8-13

Installing an RRU AISG extension cable

Lay out the cable by referring to

8.1 Cabling Requirements

, and then bind the cable

using cable ties.

Label the installed cable by referring to Attaching an L-Shaped Label.

----End

8.8 Opening the Cover Plate of an RRU Cabling Cavity

This section describes the procedure for opening the cover plate of an RRU cabling cavity.

Procedure

Step 1

Wear ESD gloves.

CAUTION

Take proper ESD protection measures, for example, wear ESD gloves, to prevent electrostatic
damage to the boards, modules, or electronic components.

Step 2

Loosen the six screws on the cover plate of the RRU cabling cavity using an M4 Phillips
screwdriver, and then open the cover plate, as shown in

Figure 8-14

RRU3201
Installation Guide

8 Installing RRU Cables

Issue 06 (2012-04-16)

Huawei Proprietary and Confidential

Summary of Contents for RRU3201

































































































Search results

Summary of Contents for RRU3201

Reviews:

Related manuals for RRU3201

Brands by name

Popular brands

Huawei RRU3201, Installation Manual

Search results

Summary of Contents for RRU3201

Reviews:

Related manuals for RRU3201

Brands by name

Popular brands