Huawei RMS-SNMP01A User Manual Download Page 4

Page: 4 / 92

RMS-SNMP01A SNMP Card
User Manual

About This Document

Issue 08 (2020-01-09)

iii

Symbol

Description

Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.

NOTICE is used to address practices not related to
personal injury.

Supplements the important information in the main text.

NOTE is used to address information not related to
personal injury, equipment damage, and environment
deterioration.

Change History

Changes between document issues are cumulative. The latest document issue contains all the
changes made in earlier issues.

Issue 08 (2020-01-09)

Deleted the Modbus-TCP feature.

Issue 07 (2019-12-20)

Updated the safety information.

Issue 06 (2019-11-26)

Updated the SNMP version description.

Issue 05 (2019-10-18)

Updated the GSM description.

Issue 04 (2017-01-19)



Added the DHCP feature.



Added the external dry contact card (RMS-RELAY02B) feature.

Issue 03 (2016-04-30)

The software version has been updated in the following aspects:



Added the CIM feature.



Added the RCCMD feature.

Issue 02 (2016-03-25)



Added the following description: The UPS2000-G used with the SNMP card does not
support the GSM modem.



Added the AI/DI module to the optional components.

Summary of Contents for RMS-SNMP01A





























































































Search results

Summary of Contents for RMS-SNMP01A

Reviews:

Brands by name

Popular brands

Huawei RMS-SNMP01A, User Manual

Search results

Summary of Contents for RMS-SNMP01A

Reviews:

Brands by name

Popular brands