manualshive.com logo in svg

Huawei Quidway S3000-EI Series, Installation Manual

Share
Download
Huawei Quidway S3000-EI Series Installation Manual Download Page 64

Installation Manual 
Quidway S3000-EI Series Ethernet Switches

 

Chapter 7    Optional Interface Modules

 

7-6

 

Table 7-6

 

Interface attributes of 1000Base-LX GL module

 

Attribute

 

Description

 

Connector

 

LC 

Number of connectors

 

1 

Transmission medium and 
maximum transmission distance

 

9/125µm Single Mode optical fiber with a maximum transmission distance 
of 40km. 

Compliant standard

 

IEEE 802.3 z 

Central wavelength

 

1550nm 

Transmitting optical power

 

-5.0dBm to 0dBm 

Receiving sensitivity

 

-21dBm 

 

7.4  10/100/1000Base-T Module 

10/100/1000Base-T module provides a 1000Base-T interface which running in 
full-duplex mode and supporting 10M, 100M, 1000M speed negotiation and 
MDI/MDI-X auto-sensing and fully compliant with IEEE 802.3ab 1000Base-T.

 

Table 7-7

 

10/100/1000Base-T module interface attributes

 

Attribute

 

Description

 

Connector

 

RJ-45 

Function

 

 

1000M full-duplex 

 

 

100M full-duplex

 

 

10M full-duplex

 

 

MDI/MDI-X auto-sensing

 

Transmission medium and 
maximum transmission distance

Category-5 twisted pair cabling. A maximum transmission distance of 100m 
is supported

 

 

7.4.1  Module Panel and the Indicators

 

10/100/1000Base-T module panel is illustrated in the following figure.

 

1000BASE-T
GT MODULE

LINK

ACTIVE

 

Figure 7-7

 

10/100/1000Base-T module panel

 

The descriptions of panel indicators are as follows:

 

Table 7-8

 

Meaning of indicators on 10/100/1000Base-T module panel

 

Indicator

 

Status description

 

LINK 

Off means that the line is disconnected. On means the line is connected.

 

ACTIVE

 

Off means that no data is being received or sent. Blinking means data is being received or sent.

 

Summary of Contents for Quidway S3000-EI Series











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands