manualshive.com logo in svg

Huawei Quidway S3000-EI Series, Installation Manual

Share
Download
Huawei Quidway S3000-EI Series Installation Manual Download Page 31

Installation Manual 
Quidway S3000-EI Series Ethernet Switches

 

Chapter 3  Installation

 

3-4

 

  Caution: 

 

 

You should first connect the grounding cable before powering on the switch.   

 

3.2.3  Redundant Power Input (Optional)

 

 

  Caution:

 

The redundant power cord is not hot-swappable.

 

 

I. Redundant power 

To make S3000-EI Series Switches more reliable, we provide redundant power 
module. The module has a (2.5v/3.3v/12v) DC external interface, which is connected 
to Huawei RPS (Redundant Power System) through DC power cord. The RPS is an 
external AC-DC or DC-DC single power switching system.

 

 The following figure illustrates the input socket of the redundant power module of 
S3000-EI Series Switches.

 

Redundant power input

Redundant power input

 

Figure 3-4

 

Appearance of the switch power socket (redundant power, S3026G for example)

 

II. Connecting redundant power cord 

Step 1: Make sure the switch has been powered off and the RPS DC output has been 
turned off.

 

Step 2: Plug one end of the DC power cord of RPS into the redundant power socket 
on the rear panel of the switch and the other end into the DC output socket of RPS.

 

Step 3: Turn on the switch power and RPS DC output.

 

Step 4: Check if the state indicator in RPS panel OK is on. On means RPS is working 
normally. Check if the RUN indicator in the switch panel is blinking. Blinking means 
the redundant power input of the switch has been correctly connected.

 

Summary of Contents for Quidway S3000-EI Series











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands