Huawei PowerCube 500 V200R001C10 Quick Manual Download Page 9

Page: 9 / 16

1. Push up the sunshade

until the spring fastener
is stuck gently.

2. Open the maintenance

compartment door.

3. Install cables for PoE cameras.

4. (Optional) Install signal cables for non-PoE cameras.

5. (Optional) Install power cables for non-PoE cameras.

Bullet camera 1

Bullet camera 2

Bullet camera 3

Dome camera

Cable distribution terminal



The power cable for the dome camera can only be connected to
the 24VAC port.



Use waterproof tape to protect the cable distribution terminal
and put it inside the pole.

6. (Optional) Install the door status sensor.

7. (Optional) Install the dome camera alarm linkage cable.

Dome camera
alarm cable

Installation Procedure

Cables  for the dome
camera  can only  be
connected  to the
PoE++ 0

–1 ports.

Bullet camera 1

Bullet camera 2

Bullet camera 3

Dome camera

NOTE

Bullet camera 1

Bullet camera 2

Bullet camera 3

Dome camera

Summary of Contents for PowerCube 500 V200R001C10

















Search results

Summary of Contents for PowerCube 500 V200R001C10

Reviews:

Related manuals for PowerCube 500 V200R001C10

Brands by name

Popular brands

Huawei PowerCube 500 V200R001C10, Quick Manual

Search results

Summary of Contents for PowerCube 500 V200R001C10

Reviews:

Related manuals for PowerCube 500 V200R001C10

Brands by name

Popular brands