Huawei PowerCube 500 V200R001C10 Quick Manual Download Page 4

Page: 4 / 16

6. Install horizontal beams.

7. Install two PV modules.

8. Install raking strut beams for the PV modules.

10.Tighten the bolts at the horizontal

beams and raking strut beams.

11.Install raking struts for the PV modules.

12.Install PV cables.

Adhesive

tape

Spacing shim

9. Install spacing shims for the

PV modules.

Spacing shim

Raking

strut beam



Keep the slots of horizontal beams facing
inwards for installing PV modules.



Partially tighten the bolts so that PV modules
can be adjusted during installation.

NOTE

Ensure that the junction boxes on the
rear of PV modules are positioned
consistently.

NOTE



Ensure that the openings of the raking
strut beams face outwards.



Partially tighten the bolts to prevent the
PV modules from sliding.

NOTE

Summary of Contents for PowerCube 500 V200R001C10

















Search results

Summary of Contents for PowerCube 500 V200R001C10

Reviews:

Related manuals for PowerCube 500 V200R001C10

Brands by name

Popular brands

Huawei PowerCube 500 V200R001C10, Quick Manual

Search results

Summary of Contents for PowerCube 500 V200R001C10

Reviews:

Related manuals for PowerCube 500 V200R001C10

Brands by name

Popular brands