Huawei OptiX RTN PI-DC B20 Product Overview And Installation Manual Download Page 13

Page: 13 / 16

Close the cover of the PI and tighten all the screws on the cover.

•Tighten the screws in sequence, as shown in the
following figure.

•Tighten all the screws on the cover (2.8

0.28 N·m).

NOTE

Mark the
positions to
drill holes.

Hole with Ф8 and a depth from
52 mm to 60 mm

Determine the positions for mounting the PI on the wall, drill holes, and install bolts. If multiple PIs need to be
mounted, reserve at lease 50 mm of space around each PI for ventilation.

Down

(Optional) Mount the PI onto a wall.

Drill holes for mounting the PI.

Mount the PI onto the wall.

CAUTION

•Before fastening the PI onto the wall, hole the PI to prevent it
from falling down.

•Before fastening the PI, ensure that its service cable holes all
face downwards.

Holes for
mounting
onto a wall

Installation Guide

Installing a PI

Small flat
washer

Big flat
washer

Nut

Summary of Contents for OptiX RTN PI-DC B20

















Search results

Summary of Contents for OptiX RTN PI-DC B20

Reviews:

Related manuals for OptiX RTN PI-DC B20

Brands by name

Popular brands

Huawei OptiX RTN PI-DC B20, Product Overview And Installation Manual

Search results

Summary of Contents for OptiX RTN PI-DC B20

Reviews:

Related manuals for OptiX RTN PI-DC B20

Brands by name

Popular brands