Huawei OptiX RTN PI-DC B20 Product Overview And Installation Manual Download Page 14 | Manualshive

Page: 14 / 16

background image

(Optional) Mount the PI onto a pole or tower.

8

Mounting
holes for
hose
clamps

Route hose clamps through mounting holes and fasten the hose clamps on the pole or tower.

1

Fasten the
hose clamps.

2

CAUTION

•Before fastening the PI onto the pole or tower, hole the PI to

prevent it from falling down.

•Before fastening the PI, ensure that its service cable holes all

face downwards.

14

Installation Guide

Installing a PI

Install the PI on the support.

Down

«
...
12
13
14
15
16
»

Summary of Contents for OptiX RTN PI-DC B20

















Reviews:

No comments

Related manuals for OptiX RTN PI-DC B20

Brand: Dawn Pages: 8

Brand: BACtrack Pages: 13

Brand: Badgematic Pages: 28

Brand: BACtrack Pages: 2

Brand: MADRIX Pages: 28

Brand: BACTcontrol Pages: 28

Brand: Campbell Pages: 2

Brand: tayco Pages: 111

Brand: Mackie Pages: 18

Brand: Mackie Pages: 2

Brand: Mackie Pages: 8

Brand: Mackie Pages: 7

Brand: B medical systems Pages: 28

Aesculap S4 Cervical

Brand: B. Braun Pages: 43

Dynamique Biski

Brand: Enabling Technologies Pages: 44

Brand: StarDental Pages: 2

Brand: USC Pages: 29

TRAKTOR KONTROL S3

Brand: Native Instruments Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands