background image

1

Product

Model

Water 

Pump

Heating and 

Humidification

Net/Gross 

Weight (kg)

Dimensions 

(mm)

(H x W x D)

Packaging 

Dimensions 

(mm)

(H x W x D)

Indoor unit 

(including 

control unit)

NetCol5000-

A011

Yes

Yes

57/74

486 x 442 x 

800

710 x 610 x 

1000

Yes

No

54/70

486 x 442 x 

800

710 x 610 x 

1000

Outdoor unit

NetCol500-

A018

N/A

N/A

83/99

966 x 1057 x 

339

1210 x 1105 x 

435

NetCol500-

A020

N/A

N/A

101/114

1327 x 966 x 

320

1485 x 1082 x 

435

1

Product Overview

Control Unit

1.1

1. Before installation, see the related manual or instructions to understand the product 

information.

2. The model described in this document is fully configured. For the components (electric heater 

and humidifier) not configured, skip the corresponding steps.

3. Use insulated tools during installation and operation.

4. Only engineers certified by the manufacturer or its agent are allowed to install, commission, 

and maintain the smart cooling product. Otherwise, personal injury or equipment damage 

may occur, and the resulting smart cooling product faults are beyond the warranty scope of 

Huawei.

5. The site electricians must be qualified.

6. Keep the outdoor unit vertical with a tilt angle not greater than 15

°

during transportation 

and storage.

7. The document is for reference only. If the product described in the document differs from the

actual product, the actual product prevails.

Copyright ©  Huawei Technologies Co., Ltd. 2020. 

All rights reserved.

Summary of Contents for NetCol5000-A011





























Reviews: