Huawei ME909s Series Hardware Manual Download Page 32

Page: 32 / 76

HUAWEI ME909s Series LTE Mini PCIe Module
Hardware Guide

RF Specifications

Issue 02 (2016-09-07)

Huawei Proprietary and Confidential

RF Specifications

4.1 About This Chapter

This chapter describes the RF specifications of the ME909s Mini PCIe module,
including:



Operating Frequencies



Conducted RF Measurement



Conducted Rx Sensitivity and Tx Power



Antenna Design Requirements



Suggestions about LTE and 2.4 GHz Wi-Fi Co-existence

4.2 Operating Frequencies

Table 4-1 an d Table 4-2 show the RF bands supported by the ME909s Mini PCIe
module.

Table 4-1

RF bands of the ME909s-821 Mini PCIe module

Operating Band

UMTS Band 1

1920 MHz

–1980 MHz

2110 MHz

–2170 MHz

UMTS Band 5

824 MHz

–849 MHz

869 MHz

–894 MHz

UMTS Band 8

880 MHz

–915 MHz

925 MHz

–960 MHz

UMTS Band 9

1749.9 MHz

–1784.9 MHz

1844.9 MHz

–1879.9 MHz

GSM 900

880 MHz

–915 MHz

925 MHz

–960 MHz

GSM 1800

1710 MHz

–1785 MHz

1805 MHz

–1880 MHz

LTE Band 1

1920 MHz

–1980 MHz

2110 MHz

–2170 MHz

LTE Band 3

1710 MHz

–1785 MHz

1805 MHz

–1880 MHz

LTE Band 8

880 MHz

–915 MHz

925 MHz

–960 MHz

LTE Band 38

2570 MHz

–2620 MHz

2570 MHz

–2620 MHz

Summary of Contents for ME909s Series













































































Search results

Summary of Contents for ME909s Series

Reviews:

Related manuals for ME909s Series

Brands by name

Popular brands

Huawei ME909s Series, Hardware Manual

Search results

Summary of Contents for ME909s Series

Reviews:

Related manuals for ME909s Series

Brands by name

Popular brands