Huawei ME909s Series Hardware Manual Download Page 47

Page: 47 / 76

HUAWEI ME909s Series LTE Mini PCIe Module
Hardware Guide

Electrical and Reliability Features

Issue 02 (2016-09-07)

Huawei Proprietary and Confidential

Description

Bands

Test Value (Unit: mA) Notes/Configuration

Typical

Idle

LTE

LTE bands

Module is powered up.

DRX cycle=8 (2.56s)

Module is registered on the
network.

USB is in active.

HSPA+/WCDMA UMTS bands

Module is powered up.

DRX cycle=7 (1.28s)

Module is registered on the
network, no data is transmitted.

USB is in active.

GPRS/EDGE

GSM bands

Module is powered up.

MFRMS=5 (1.175s)

Module is registered on the
network, no data is transmitted.

USB is in active.

Table 5-7

Averaged Data Transmission DC power consumption of ME909s-821 Mini

PCIe module (HSPA/WCDMA/TD-SCDMA/LTE)

Description

Band

Test Value Units

Power (Unit: dBm)

WCDMA

Band 1
(IMT2100)

226

0 dBm Tx Power

308

10 dBm Tx Power

830

23.5 dBm Tx Power

Band 9

(J1700)

220

0 dBm Tx Power

257

10 dBm Tx Power

511

23.5 dBm Tx Power

Band 5

(850 MHz)

220

0 dBm Tx Power

257

10 dBm Tx Power

511

23.5 dBm Tx Power

Band 8

(900 MHz)

221

0 dBm Tx Power

258

10 dBm Tx Power

541

23.5 dBm Tx Power

HSDPA

Band 1

(IMT2100)

186

0 dBm Tx Power

227

10 dBm Tx Power

Summary of Contents for ME909s Series













































































Search results

Summary of Contents for ME909s Series

Reviews:

Related manuals for ME909s Series

Brands by name

Popular brands

Huawei ME909s Series, Hardware Manual

Search results

Summary of Contents for ME909s Series

Reviews:

Related manuals for ME909s Series

Brands by name

Popular brands