Huawei LUNA2000-5-NHE0 User Manual Download Page 81

Page: 81 / 95

Alarm ID

Alarm

Name

Alarm

Severity

Possible Cause

Troubleshooting

3009

Battery

expansio

module

low

temperat

ure

Minor

1. The ambient

temperature is excessively

low.
2. A battery expansion

module is abnormal.

1. Check whether the ambient

temperature in the installation

positions of the [Battery-1/2

battery expansion

module-1/2/3] battery

expansion modules is lower than

the lower threshold.
2. If the ambient temperature is

excessively low, improve the

installation environment.
3. If the alarm persists after the

ambient temperature becomes

normal, contact your dealer or

Huawei technical support.

3010

Battery

expansio

module

short

circuit

Major

1. A battery expansion

module is short-circuited.
2. A battery expansion

module is abnormal.

1. Turn off the inverter AC

output switch, inverter DC input

switch, and battery DC switch,

and wait for 5 minutes.
2. Check the power cable

connection to the [Battery-1/2

battery expansion

module-1/2/3] battery

expansion modules by referring

to the quick installation guide. If

the cable is damaged or short-

circuited, replace it.
3. After checking that the cables

are correctly connected, turn on

the battery DC switch, AC output

switch, and inverter DC input

switch in sequence.
4. If the alarm persists, contact

your dealer or Huawei technical

support.

3011

Battery

expansio

module

undervol

tage

Warning The voltage of a battery

expansion module is low.

If the sunlight is sufficient or AC

reverse charging is allowed, the

[Battery-1/2 battery expansion

module-1/2/3] battery

expansion modules can be

charged when the inverter is

running.

LUNA2000-(5-30)-NHS0

User Manual

7 System Maintenance

Issue 06 (2022-03-01)

Summary of Contents for LUNA2000-5-NHE0
































































































Search results

Summary of Contents for LUNA2000-5-NHE0

Reviews:

Related manuals for LUNA2000-5-NHE0

Brands by name

Popular brands

Huawei LUNA2000-5-NHE0, User Manual

Search results

Summary of Contents for LUNA2000-5-NHE0

Reviews:

Related manuals for LUNA2000-5-NHE0

Brands by name

Popular brands