manualshive.com logo in svg

Huawei eSpace IPC1201-VR, Installation Manual, Page: 3 / 92

Share
Download
Huawei eSpace IPC1201-VR Installation Manual Download Page 3

IPE 
Installation Guide  

About This Document 

 

Issue 03 (2013-02-28) 

Huawei Proprietary and Confidential           

Copyright © Huawei Technologies Co., Ltd    

ii 

 

About This Document 

Purpose 

This document describes the installation procedure and technical specifications of IP Cameras 
(IPCs) of the following models: eSpace IPC1601, eSpace IPC1201-VR, eSpace IPC1602, 
eSpace IPC2602, eSpace IPC5602, eSpace IPC2202-VR, eSpace IPC2203-VR, eSpace 
IPC5201-VR , eSpace IPC5202-VR, eSpace IPC5603, eSpace IPC1701-VR-VP, eSpace 
IPC1701-VF-VP, eSpace IPC2702-VF-VP, eSpace IPC2702-VR-VP, eSpace IPC5702-VR-VP,  
eSpace IPC1801-Z36, eSpace IPC1901-Z36, eSpace IPC2802-Z18, eSpace IPC2902-Z18, 
eSpace IPC5802-Z20, and eSpace IPC5902-Z20. 

Intended Reader 

This manual is intended for professional system maintenance or installation engineers. 

Symbol Conventions 

The symbols that may be found in this document are defined as follows. 

Symbol 

Description 

 

Indicates a hazard with a high level or medium leve l of 
risk which, if not avoided, could result in death or serious 
injury. 

 

Indicates a hazard with a low level of risk which, if not 
avoided, could result in minor or moderate injury. 

 

Indicates a potentially hazardous situation that, if not 
avoided, could result in equipment damage, data loss, 
performance deterioration, or unanticipated results. 

 

Provides a tip that may help you solve a problem or save 
time. 

 

Provides additional information to emphasize or 
supplement important points in the main text. 

 

Summary of Contents for eSpace IPC1201-VR





























































































Reviews:

No comments