Huawei Enterprise S2700 Series Configuration Manual Download Page 35 | Manualshive

Page: 35 / 354

background image

l

Dense mode: applies to continuous sub-interface numbering.

----End

1.3.7 Checking the Configuration

After SNMPv2c functions are configured, you can view the SNMPv2c configurations.

Prerequisite

The configurations of basic SNMPv2c functions are complete.

Procedure

l

Run the

display snmp-agent community

command to check the configured community

name.

l

Run the

display snmp-agent sys-info

version

command to check the enabled SNMP

version.

l

Run the

display acl

acl-number

command to check the rules in the specified ACL.

l

Run the

display snmp-agent mib-view

command to check the MIB view.

l

Run the

display snmp-agent sys-info

contact

command to check the equipment

administrator's contact information.

l

Run the

display snmp-agent sys-info

location

command to check the location of the

device.

l

Run the

display snmp-agent target-host

command to check information about the target

host.

l

Run the

display snmp-agent inform

[

address

udp-domain

ip-address

[

vpn-instance

vpn-instance-name

]

params

securityname

security-string

] command to check inform

parameters and device statistics with the NM station being specified or not.

l

Run the

display snmp-agent notification-log info

command to check alarm logs stored

in the log buffer.

l

Run the

display snmp-agent extend error-code status

command to check whether the

SNMP extended error code feature is enabled.

l

Run the

display constant-ifindex configuration

command to check the constant interface

index function and relevant configuration information.

----End

1.4 Configuring a Device to Communicate with an NM
Station by Running SNMPv3

After SNMPv3 is configured, a managed device and an NM station can run SNMPv3 to
communicate with each other. To ensure normal communication, you need to configure both
sides. This section describes only the configurations on a managed device (the agent side). For
details about configurations on an NM station, see the pertaining NM station operation guide.

The NM station manages a device in the following manners:

l

Sends requests to the managed device to perform the GetRequest, GetNextRequest,
GetResponse, GetBulk, or SetRequest operation, obtaining data and setting values.

Quidway S2700 Series Ethernet Switches
Configuration Guide - Network Management

1 SNMP Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

25

«
...
33
34
35
36
37
...
»

Summary of Contents for Enterprise S2700 Series



































































































































































































































































































































































Reviews:

No comments

Related manuals for Enterprise S2700 Series

ICS-G7748A Series

Brand: Moxa Technologies Pages: 10

Brand: iBall Baton Pages: 9

RUGGEDMAX WIN7000

Brand: RuggedCom Pages: 42

SteelCentral NetExpress

Brand: Riverbed Pages: 38

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

Brand: Cowfish Technologies Pages: 38

Brand: Supermicro Pages: 27

Brand: Westermo Pages: 34

Brand: 3Com Pages: 12

Brand: Hama Pages: 24

Brand: Softing Pages: 16

Brand: ExtraHop Pages: 3

Brand: DPS Telecom Pages: 80

Brand: Tripp Lite Pages: 2

Brand: Omron Pages: 4

Brand: METREL Pages: 21

Brand: peplink Pages: 111

Brand: LevelOne Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands