Huawei Enterprise S2700 Series Configuration Manual Download Page 313

Page: 313 / 354

Step 3

Run the

restart

command in the NQA instance view to restart an NQA test instance.

----End

6.18.2 Clearing NQA Statistics

When the statistics on the current test instance are saved to the FTP server, you can clear test
results on the device.

Prerequisite

NQA statistics cannot be restored after you clear them. So, confirm the action before you use
the command.

Context

NOTE

Statistics about the test being performed cannot be cleared.

Procedure

Step 1

Run the

system-view

command, enter the system view.

Step 2

Run the

nqa

test-instance

admin-name

test-name

command, enter the NQA test instance view.

Step 3

Run the

clear-records

command in the NQA view to clear history statistics on NQA tests and

test results.

----End

6.18.3 Debugging NQA

This part describes how to debug test instances.

Prerequisite

When a fault occurs, run the following

debugging

command in the user view to debug NQA

and locate the fault.

Context

CAUTION

Debugging affects the performance of the system. So, after debugging, run the

undo debugging

all

command to disable it immediately.

Procedure

Step 1

Run the

debugging nqa all

command in the NQA view to enable NQA debugging.

----End

Quidway S2700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

303

Summary of Contents for Enterprise S2700 Series



































































































































































































































































































































































Search results

Summary of Contents for Enterprise S2700 Series

Reviews:

Related manuals for Enterprise S2700 Series

Brands by name

Popular brands

Huawei Enterprise S2700 Series, Configuration Manual

Search results

Summary of Contents for Enterprise S2700 Series

Reviews:

Related manuals for Enterprise S2700 Series

Brands by name

Popular brands