Home
/
Huawei
/
Enterprise S2700 Series
/
Configuration Manual

Huawei Enterprise S2700 Series, Configuration Manual, Page: 237 / 354

Share

Page: 237 / 354

Huawei Enterprise S2700 Series Configuration Manual Download Page 237

interface vlanif

vlan-id

The interface to send multicast NTP packets is specified.

Step 4

Run:

ntp-service multicast-server

[

authentication-keyid

key-id

|

version

number

]*

The ID of the authentication key used by the NTP multicast server is configured.

For configuring the multicast client, see

Configuring the Broadcast Mode

.

----End

4.4.8 Checking the Configuration

After NTP security mechanisms are configured, you can view the configuration.

Prerequisite

The configurations of the NTP Security Mechanisms are complete.

Procedure

l

Run the

display ntp-service status

command to view the status of the NTP service.

l

Run the

display ntp-service sessions

[

verbose

] command to view the status of NTP

sessions.

----End

Example

Run the

display ntp-service status

command to view the status of the NTP service.

<Quidway>

display ntp-service status

clock status: synchronized
clock stratum: 2
reference clock ID: LOCAL(0)
nominal frequency: 60.0002 Hz
actual frequency: 60.0002 Hz
clock precision: 2^18
clock offset: 0.0000 ms
root delay: 0.00 ms
root dispersion: 0.00 ms
peer dispersion: 10.00 ms
reference time: 15:51:36.259 UTC Apr 25 2010(C6179088.426490A3)

Run the

display ntp-service sessions

[

verbose

] command to view the status of NTP sessions.

<Quidway>

display ntp-service sessions

source reference stra reach poll now offset delay
disper
********************************************************************************
[12345]127.127.1.0 LOCAL(0) 7 1 64 2 - 0.0
15.6
note: 1 source(master),2 source(peer),3 selected,4 candidate,5 configured,
6 vpn-instance

4.5 Maintaining NTP

This section describes how to debug NTP through the debugging command in case of an NTP
operation fault.

Quidway S2700 Series Ethernet Switches
Configuration Guide - Network Management

4 NTP Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

227

«
...
235
236
237
238
239
...
»

Summary of Contents for Enterprise S2700 Series



































































































































































































































































































































































Reviews:

No comments