Huawei Enterprise S2700 Series Configuration Manual Download Page 293

Page: 293 / 354

Data Preparation

To configure the UDP test, you need the following data.

No.

Data

Administrator name and test name

IP address and port of the UDP server

Destination IP addresss and the port of the probe packets sent by the UDP client

(Optional) Source IP addresses and source port numbers of test packets, interval for
sending test packets, and percentage of the failed NQA tests

Start mode and end mode of the test

6.13.2 Configuring the UDP Server

The IP address and number of the port monitored by the server must be identical with those
configured on the client.

Context

Do as follows on the NQA server (UDP server):

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

nqa-server udpecho

ip-address

port-number

The UDP monitoring service is configured.

Note that the IP address and port number monitored by the server should be consistent with those
configured on the client.

----End

6.13.3 Configuring the UDP Client

This part describes how to set UDP test parameters.

Context

Do as follows on the NQA client (UDP client):

Quidway S2700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

283

Summary of Contents for Enterprise S2700 Series



































































































































































































































































































































































Search results

Summary of Contents for Enterprise S2700 Series

Reviews:

Related manuals for Enterprise S2700 Series

Brands by name

Popular brands

Huawei Enterprise S2700 Series, Configuration Manual

Search results

Summary of Contents for Enterprise S2700 Series

Reviews:

Related manuals for Enterprise S2700 Series

Brands by name

Popular brands