background image

4

SWERV

® 

INSTALLATION AND ASSEMBLY

HANDPIECE CORD CONNECTION

Align the marks on the control unit and the handpiece cord 

plug. Firmly push the plug into the connector at the front of the 

control unit. (Fig. 1)

CAUTION: 

1.   Do not disconnect the handpiece cord when power to device 

is switched on and the footswitch is depressed.

2.   Detach insert before removing handpiece cord.
3.   Grip the plug of the handpiece cord when removing.

ULTRASONIC INSERT CONNECTION

Select appropriate kHz insert (25 or 30) for the generator. 

Fill handpiece with water. While holding the handpiece in 

an upright position, activate the purge function or the foot 

control to remove any air bubbles that may be trapped inside 

the handpiece. Lubricate the rubber o-ring on the sterilized 

insert with water prior to placing it into the handpiece. Fully 

seat the insert with a gentle push-twist motion. Do not force 

the insert into the handpiece. 

WARNING:

 Always use water when operating the unit to keep 

the handpiece and insert cool. Minimum recommended setting 

>10 m l/min. Maximum recommended setting < 50 ml/min. 

FOR OPERATION

  Verify that the water supply is adequate and clean prior to 

beginning each procedure. 

 Purge handpiece.

  Use a Hu-Friedy disposable barrier sleeve (UMBS) on the handpiece. Replace the barrier between 

patients. Properly dispose of the barrier in accordance with guidelines for contaminated waste 

materials. 

 Place insert in handpiece.

 Adjust the power level to the recommended mode. 

 Depress the foot control to start insert vibration. 

  Turn the water adjustment knob counterclockwise gradually to increase the water flow. (Fig. 2) 

WHEN TREATMENT IS COMPLETED

1.   Release the foot control and place the handpiece in the handpiece holder. (Fig. 3)
2.  Turn off the power switch.
3.   Hold handpiece in upright position. Gently pull the insert out of the handpiece opening.  

Ultrasonic inserts are easily interchangeable for various applications and procedures.

4. Close the dental unit’s water valve. 

5

1

7

2

8

3

Summary of Contents for SWERV3













Reviews: