background image

 

  HTI Filtration INC.  

           

 

7716 Gary Watson Pt.  ● Colorado Springs ● CO 80915 ● USA ● Ph 719-490-8800 ● [email protected]  

 

 

 

 

 

 

 

 

 

 

 

 

 

                           

 

                                  STANDARD WARRANTY 

 
 
This filter system was inspected before shipment from our plant. To the original purchaser of this system, 
HTI Filtration warrants its products free from defects in material and workmanship for a period of one (1) 
year from date of purchase. 
 
HTI Filtration makes no other express warranty and excludes (and buyer waives) any and all implied 
warranties including, without limitation to, implied warranties in connection with the design, sale, 
merchantability or fitness of the goods for any particular use or purpose. 
 
In order for any claim under this warranty to be valid, HTI Filtration must receive notice in writing from the 
buyer, (within a reasonable time period, not to exceed thirty (30) calendar days after any defect is 
discovered. The claim must include a detailed report of the conditions of use at the time of discovery of 
defect. Parts which fail or become defective during the warranty period (except as a result of freezing, 
melting, improper installation, use or care), shall be replaced or repaired at HTI Filtration’s option at no 
charge within 90 days of the receipt of the defective part, barring unforeseen delays. HTI Filtration shall in 
no event be responsible for the repairs made by others without the express written permission and consent 
of HTI Filtration. 
 
To obtain warranty replacement or repairs, defective components or parts should be returned, freight 
prepaid, to place of purchase or nearest authorized service center. HTI Filtration shall not be responsible 
for cartage, removal and/or reinstallation labor or any other such costs incurred in obtaining warranty 
replacements. In no event shall HTI Filtration be responsible for any incidental or consequential damage, 
whether foreseeable or not and whether or not such damage occurs or is discovered before or after repair 
or replacement. 
 
The forgoing warranty does not apply to wear components, seals or filtration elements. 
 
This warranty extends only to the original buyer and HTI Filtration makes no other warranty, expressed or 
implied, to other persons or entities. If buyer makes any warranty or representation inconsistent with or in 
addition to the warranty stated hereinabove, the buyer shall, at its own expense, defend and hold HTI 
Filtration harmless from any claim thereon of any nature whatsoever. 
 

 
 
                           

Summary of Contents for 810-050.2












Reviews: