HS-Technik TorqBee TBASL-10-2 Operating Instructions Manual Download

Page: 33 / 36

CE Declaration of conformity

We, the manufacturer, hereby declare that the named tool complies with the essential

protection requirements of the listed EU directives regarding design and construction type.

The prerequisite for this is the intended use of the tool as well as compliance with the

installation and commissioning instructions.

If the product or its accessories are modified without our permission, this declaration be

comes invalid.

Tool description:

Battery shut-off screwdriver

Type designation:

TBASL-x…

Manufacturer:

HS-Technik GmbH

Im Martelacker 12

D-79588 Efringen-Kirchen

Directives:

2006/42/EU

2014/30/EU

Applied standards:

DIN EN ISO 12100 2011-03

EN 62841-1:2015+AC:2015, EN 62841-2-2:2014

EN 61000-6-3:2007+A1:2011+AC:2012, EN 61000-6-

2:2005+ AC:2005

EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997+

AC:1997+A1:2001+A2:2008

HS-Technik GmbH

Im Martelacker 12, D-79588 Efringen-Kirchen

February 2021

Florian Hanke

CEO

Summary of Contents for TorqBee TBASL-10-2





































Search results

Summary of Contents for TorqBee TBASL-10-2

Reviews:

Related manuals for TorqBee TBASL-10-2

Brands by name

Popular brands

HS-Technik TorqBee TBASL-10-2, Operating Instructions Manual

Search results

Summary of Contents for TorqBee TBASL-10-2

Reviews:

Related manuals for TorqBee TBASL-10-2

Brands by name

Popular brands