HS-Technik TorqBee TBASL-10-2 Operating Instructions Manual Download | Manualshive

Page: 22 / 36

background image

- 22 -

4.2.2 Press start button

Pressing or releasing the start button starts or stops the tool.

NOTE

The tool only starts when the battery has sufficient capacity.

4.2.3 Front LED

WARNING

Risk of injury from the light emitting diode

Looking directly into the light emitting diode can lead to eye injuries.

• Never look directly into the light emitting diode.

The LED on the front of the tool is used to illuminate the assembly area. After pressing the

start key, the LED switches on. It turns off automatically after a few seconds.

* - Front LED

*

«
...
20
21
22
23
24
...
»

Summary of Contents for TorqBee TBASL-10-2





































Reviews:

No comments

Related manuals for TorqBee TBASL-10-2

Brand: Oemtools Pages: 8

Brand: SAMCHULLY Pages: 24

ASCM18QM Series

Brand: Fein Pages: 20

Brand: Jarvis Pages: 12

Brand: hager Pages: 4

Brand: hager Pages: 2

Brand: Paslode Pages: 16

Brand: Marson Pages: 6

Brand: VOLTEQ Pages: 5

EPSITRON 787-712

Brand: WAGO Pages: 2

Brand: Lumberjack Pages: 14

Brand: Pulsar Pages: 2

Brand: RIDGID Pages: 40

Brand: Westfalia Pages: 46

7 138 02 62 09 0

Brand: Fein Pages: 105

Brand: Wacker Neuson Pages: 74

Brand: Fein Pages: 31

Brand: KRAUSMANN Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands