background image

4/28/2017                                                        860-EI 

 

High / Low Models: Antenna Extension Cable Mounting 

 

 

 
Antenna Removal- (If extension not attached) 
 

 

1.

 

Antenna 

a)

 

Locate antenna on valve box inside fire pit 

enclosure. Remove antenna where attached to 
valve box using fingers on knurled part of antenna 
ferrule base. 
 

NOTE: 

If needed use needle nose pliers and gently grasp the 

knurled ferrule base of the antenna and loosen finishing with 
fingers. 

 

 

2.

 

Antenna Extension Cable

 

 

NOTE:

 Before starting, straighten antenna extension 

cable it will make it easier to work with during 
assembly. 

 

a)

 

Attach female end of antenna extension cable to 

valve box finger tight. On hex part, use a 5/16” 

open end wrench to snug up the attachment of 
cable to valve box.

 

*** Do Not Overtighten 
 

 

3.

 

Antenna Attachment 

a)

 

Attach antenna to extension cable and firmly 

tightening with fingers. Antenna should rotate with 
mild resistance without coming loose.  
 

4.

 

Bracket Attachment 

a)

 

Clip on the two nylon attachment brackets to the 

cable near the antenna. Position the brackets based 
on the desired location to be attach to the interior 
of your fire pit enclosure.

 

 
NOTE:

 The optimum location for signal strength is near the 

vent facing in the general area where the remote will be used. 
The exposed tip of the antenna at the vent to be 

approximately 1/2” or more (4b).   

 

 

b)

 

Place the cable brackets with the antenna at the 

position where attachment will be. Mark those two 
spots on the surface through the attachment bracket 
holes 

c)

 

Drill two holes into the enclosure using a 3/16” 

masonry drill bit or equivalent bit depending on the 
type of material you are attaching to.  

d)

 

Assemble the antenna cable assembly to the interior 

wall or surface of the fire pit using two Tapcon or 
equivalent fasteners. 

 

5.

 

Antenna Adjustment   

a)

 

With the antenna now mounted you have some 
limited adjustment with this. Be cautious when 
rotating and repositioning the antenna so not to 
break or damage.

 

 

 

 

 

 
 
 
 
 

Summary of Contents for 49X8SSEI-L
























Reviews: