HP StorageWorks A7298A Manual Download Page 66

Page: 66 / 82

5–12

host bus adapter for Windows and Linux installation guide

Diagnostic and Configuration Utilities

Input/Output

Choose this option to open or close input and output files. The contents of the Input
file are interpreted and executed by the program. The output file contains a log of all
messages. Note that nesting of input files is not supported.

Show Host Bus Adapter Info (For lputilnt Only)

Choose this option to display HBA data in these areas:

•

BIU PCI Configuration Parameters

•

Host Bus Adapter Info and Status

•

Adapter Revisions

•

Display Configuration Data

•

Service Parameters

•

Status/Counters Info

•

Link Status

•

Link Attention

Quit the LightPulse Utility/NT Utility

Choose this option to exit the program. A warning message indicates if any errors
were encountered during the session.

Summary of Contents for StorageWorks A7298A



















































































Search results

Summary of Contents for StorageWorks A7298A

Reviews:

Related manuals for StorageWorks A7298A

Brands by name

Popular brands

HP StorageWorks A7298A, Manual

Search results

Summary of Contents for StorageWorks A7298A

Reviews:

Related manuals for StorageWorks A7298A

Brands by name

Popular brands