HP StorageWorks A7298A Manual Download Page 7

Page: 7 / 82

host bus adapter for Windows and Linux installation guide

vii

About this Guide

This user guide provides information to help you:

•

Install, configure, and use the diagnostic utilities for the HP StorageWorks
A7298A host bus adapter for Windows and Linux platforms.

•

Contact technical support for additional assistance

Intended Audience

This book is intended for use by system administrators who are experienced with the
following:

•

Windows Advanced Server Limited Edition v1.2

•

Linux Red Hat Advanced Workstation v2.1 (Itanium processor)

•

Host bus adapters

Related Documentation

In addition to this guide, refer to the host bus adapter for Windows and Linux release
notes.

Summary of Contents for StorageWorks A7298A



















































































Search results

Summary of Contents for StorageWorks A7298A

Reviews:

Related manuals for StorageWorks A7298A

Brands by name

Popular brands

HP StorageWorks A7298A, Manual

Search results

Summary of Contents for StorageWorks A7298A

Reviews:

Related manuals for StorageWorks A7298A

Brands by name

Popular brands